Prevention of Pool Cover Installation Mistakes

The pool industry has been apt in both the safety and automatic cover sectors. Throughout the years, the pool and spa experts have become comfortable estimating and installing these items. Contractors are now familiar with the procedure.This article reviews the probable pool cover installation mistakes and how to avoid them.

There are minimal pool cover installation mistakes than before.

vice president of sales for Cover Pools, Barry Greenwald

Safety Covers

Improper overlap

Those who have no idea of how the safety covers functions may not comprehend the need for exact measurements. The cover should be a replica of the pool’s form. Installers ought to get the exact safety cover measurements to fit the pool. It is not about attempting to place an oversize cover on a pool.

At times, experts install the covers in a crooked manner, such that the overlap in one end is way smaller than the other. Proper overlap is key to achieving its safety function and avoid pool cover installation mistakes.

Overlapping can also reduce the covers’ lifespan. Wrong-shaped covers and improper overlaps make the fabric rub against the deck causing wear and tear. A material meant to last 12-15 years, in a worst-case scenario, only serves for 3 years. This is a great disservice to the user.

Errors in the A-B method implementation

The technique for estimating free form covers is a bit complicated, and some experts don’t get it correct. A number install the poles at an inaccurate distance from the pool or from each other. The poles should be 3-feet apart from the waterline, lest the image will be inaccurate.

Some interchange the measurements of A and B. When facing the pool, point A is to the left and point B to the right. Interchanging the measurements will have the cover made upside down.

Incorrect pool cover installation around obstructions

When placing covers around water features and high walls, the objective is to minimize interference. To work around this problem, installers support some parts of the cover on a cable system, making it less disruptive. This, however, should not be the lazy way out as it compromises safety and maintenance. Using this method will leave a 4- inch gap that permits the entry of debris as well as become a safety risk.

Moreover, producers report projects where builders place covers too high from the obstructions. The problem with this is it uses up extra material hence unable to fit the rest of the pool. Second, during winter, the material will be unable to bear snow loads. The best solution in massive features is to float using a raft as you drill through the wall.

When carrying out pool cover installation, it is best to begin with the obstruction to guarantee a cozy fit for the other features. Here, there is no chance of overlap, therefore minimizing errors.

Space to stretch

After some time, the fabric may stretch due to gravity and snowfalls. Many times, installers don’t create accurate tension to allow for this. This happens when they place the anchors near the cover, or disregard to change the spring tension appropriately.

The spring’s tension should be tight so that if the cover stretches, it will still maintain its tightness.

Automatic Cover

Not settling the pool or vault

The success of automatic pool cover installation lies in exact measurements. Even a small wrinkle can prevent the cover from opening and shutting.

This is the point of majority pool cover installation mistakes. It’s not about the shape you visualize; rather, it takes time to take accurate measurements, especially the width of the cover, cover drum, and lead edge bar.

Heavy masonry lids

The brick lids ought to be at a similar height as the deck. The trays and brackets anchoring them can’t be too low that they meddle with the capability of the cover to the spindle. If the lid is too bulky, place the brackets and tray low. The total of all the lid components ought not to be bulkier than the adapting.

In addition, use light and small pieces that one can be able to lift. Not only about the weight, but also avoid weird shapes such as long rectangles.

Inaccurate placing of the mechanism

The system ought to be level with the track. This lessens the measure of work by the system. If it’s excessively low, it delays the cover as it rises and lowers into the pool. This causes either the cover or motor to wear earlier. Furthermore, it ought to be between the tracks, failure to which the cover won’t open and close correctly.

Cutting the track or ropes too short

Cutting ropes and tracks are vital to fit the task. The problem is that most installers cut them too short. On the rope, a short rope means the cover can’t be fully open. To avoid this, cut the rope when the cover is open.

On the track, a short track has its misgivings. The track joins the guide and the end of the track, combining the plates. This is impossible if the track is short. Furthermore, when the track makes a sharp angle as the material spools from the roller, it wears the track and covers edge due to excessive pressure on the load.